Showing posts with label IC Amplifier. Show all posts
Showing posts with label IC Amplifier. Show all posts

Wednesday, April 6, 2022

14V 4 Channel 200W MOSFET Quad Bridge Power Amplifier using TDA7850 with PCB

Fig. 1 - 14V 4 Channel 200W MOSFET Quad Bridge Power Amplifier using TDA7850 with PCB

Unleash Power and Sound with a 14V 4-Channel 200W MOSFET Quad Bridge Amplifier using TDA7850 and PCB

This is a 14V 4 Channel 200W MOSFET Quad Bridge Power Amplifier, it uses an TDA7850 Integrated Circuits, in Quad Bridge Mode to drive four power speakers.

The circuit provides a total output power of 200W, and this with good sound quality, powered from a unipolar 14V power supply.

The Amplifier responds very well to all audible frequency ranges, and has a minimalist, compact design, which makes this amplifier a good choice for an unprecedented range of application. 

IC Description

The TDA7850 is a breakthrough MOSFET technology Class AB audio power amplifier in Flexiwatt 25 package designed for high power car radio. 

The fully complementary P-Channel / N-Channel output structure allows a rail to rail output voltage swing which, combined with high output current and minimized saturation losses sets new power references in the car-radio field, with unparalleled distortion performances. The TDA7850 integrates a DC offset detector.

You might also be interested in:

IC Features

  • High output power capability:
    • 4 x 50W / 4Ω max.
    • 4 x 30W / 4Ω @ 14.4 V, 1 kHz, 10 %
    • 4 x 80W / 2Ω max.
    • 4 x 55W / 2Ω @ 14.4V, 1 kHz, 10 %
  • MOSFET output power stage
  • Excellent 2Ω driving capability
  • Hi-Fi class distortion
  • Low output noise
  • ST-BY function
  • Mute function
  • Auto mute at min. supply voltage detection
  • Low external component count:
    • Internally fixed gain (26 dB)
    • No external compensation
    • No bootstrap capacitors
  • On board 0.35 A high side driver

The Schematic Circuit

In Figure 2 below, we have available the schematic diagram of the 14V 4 Channel 200W MOSFET power amplifier circuit, this circuit is quite simple to assemble.

As we can see there are very few external components, making the circuit very simple to assemble, even for a technician or hobbyist with little experience in electronics can assemble it without much difficulty. 

Fig. 2 - Diagram 14V 4 Channel 200W MOSFET Quad Bridge Power Amplifier using TDA7850

It is important to remember to be careful when assembling the circuit, as simple as the circuit is. We must be careful not to invert any components, such as capacitors, or invert the input voltage of the circuit, because the integrated circuit or other components can be damaged easily.

Components List

  • Semiconductors
    • U1 ............ TDA7850 Integrated Circuit 

  • Resistors
    • R1 ............ 47KΩ Resistor (yellow, violet, orange, gold)
    • R2, R3 ..... 10K resistor (brown, black, orange, gold)

  • Capacitors
    • C1 to C4 ... 220nF Ceramic/Polyester Capacitor
    • C5, C6 ...... 1μF Ceramic/Polyester Capacitor
    • C7 ............. 470nF Ceramic/Polyester Capacitor
    • C8 ............. 47μF / 25V Electrolytic Capacitor
    • C9 ............. 2.200μF / 25V Electrolytic Capacitor
    • C10 ........... 100nF Ceramic/Polyester Capacitor

  • Miscellaneous
    • P1 to P9 .... Screw Terminal Type 5mm 2-Pin Connector
    • Other ........ PCB, Wires, Speaker, etc.

    Power Supply

    This amplifier is powered by unipolar source, with direct current, the maximum current required by the circuit is approximately 15 Amperes.

    And you can connect it directly to a car battery, or a motorcycle battery, or a no-break battery, or a bench power supply... 

    The power will be according to the power supply, and as already shown in the IC features above, to have 4 outputs of 50W we have to supply the circuit with 14.4V

    Printed Circuit Board

    In Figure 3, we provide the PCB - Printed Circuit Board, in GERBER, PDF and PNG files. These files are available for free download, on the MEGA server, in a direct link, without any bypass. 

    All to make it easier for you to do a more optimized assembly, either at home, or with a company that prints the board. You can download the files in the Download option below.

    Fig. 3 - PCB 14V 4 Channel 200W MOSFET Quad Bridge Power Amplifier using TDA7850

    Files to Download, Direct Link:

    Click on the link beside: GERBER, PDF and PNG files

    I hope you enjoyed it!!!

    If you have any questions, suggestions or corrections, please leave them in the comments and we will answer them soon.

    Subscribe to our blog!!! Click here - elcircuits.com!!!

    My Best Regards!!!

    Tuesday, February 15, 2022

    High Performance 56W Audio Power Amplifier using LM3876 IC with PCB

    Fig. 1 - High Performance 56W Audio Power Amplifier using LM3876 IC with PCB

    This is a High Performance 56W Audio Power Amplifier, based on the LM3876 Integrated Circuit, with great sound quality, powered by a symmetrical power supply.

    The Amplifier responds very well in all audible frequency ranges from 20Hz to 20Khz, and has a minimalistic and very compact design, which makes this amplifier a good choice to be assembled with little difficulty.

    LM3876 Integrated Circuit Description

    The LM3876 is a high-performance audio power amplifier capable of delivering 56W of continuous average power to an load with 0.1% THD+N from 20Hz–20kHz.

    The performance of the LM3876, utilizing its Self Peak Instantaneous Temperature (°Ke) (SPiKe) protection circuitry, puts it in a class above discrete and hybrid amplifiers by providing an inherently, dynamically protected Safe Operating Area (SOA) SPiKe protection. 

    Means that these parts are completely safe-guarded at the output against overvoltage, under-voltage, overloads, including shorts to the supplies, thermal runaway, and instantaneous temperature peaks.

    The LM3876 maintains an excellent signal-to-noise ratio of greater than 95dB (min) with a typical low noise floor of 2.0μV. It exhibits extremely low THD+N values of 0.06% at the rated output into the rated load over the audio spectrum, and provides exceptional linearity with an IMD (SMPTE) typical rating of 0.004%.

    Feature

    • 56W Continuous Average Output Power into 8Ω
    • 100W Instantaneous Peak Output Power Capability
    • Signal-to-Noise Ratio ≥ 95 dB(Min)
    • An Input Mute Function
    • Output Protection from a Short to Ground or to the Supplies Via Internal Current Limiting Circuitry
    • Output Over-Voltage Protection against Transients from Inductive Loads
    • Supply Under-Voltage Protection, not Allowing Internal Biasing to Occur when |VEE| + |VCC| ≤ 12V, thus Eliminating Turn-On and Turn-Off Transients
    • 11-Lead TO-220 Package
    • Wide Supply Range 20V - 94V

    The Schematic Circuit

    In Figure 2 below we have components arrangement of the power amplifier circuit with the LM3876 IC, and as we can see, the difficulty is not extreme. 

    Since there are few external components, making the amplifier circuit very simple to assemble, and a technician or hobbyist with medium experience can assemble it without much difficulty. 

    Fig. 2 - Schematic Circuit High Performance 56W Audio Power Amplifier using LM3876 IC

    It is important to remember to be careful when assembling the circuit, not to invert any component such as capacitor diodes, or even when connecting the symmetrical voltage of the power supply. Not to invert the voltage poles, because the integrated circuit or other components can be damaged.

    The coil is formed is a 5uH coil, for those who are going to assemble it, you can assemble it with 10 turns of 18 AWG Wire with a 3/8" air core.

    Components List

    • Semiconductors
      • U1 .............. LM3876 Integrated Circuit

    • Resistors
      • R1, R5 ....... 1K resistor (brown, black, red, gold)
      • R2, R3 ....... 18K resistor (brown, gray, orange, gold)
      • R4 .............. 10K resistor (brown, black, orange, gold)
      • R6, R7 ....... 22K resistor (red, red, orange, gold)
      • R8 .............. 100Ω resistor (brown, black, brown, gold)
      • R9 .............. 10Ω / 1W resistor (brown, black, black, gold)
      • RP1 ............ 10K Potentiometer

    • Capacitors
      • C1 ................. 2.2μF Ceramic/Polyester Capacitor
      • C2 ................. 220pF Ceramic/Polyester Capacitor
      • C3 ................. 47 Ceramic/Polyester Capacitor
      • C4, C5 .......... 22μF / 65V Electrolytic Capacitor
      • C6, C7, C8 .... 0.1uF Ceramic/Polyester Capacitor
      • C9, C10 ......... 2.200uF / 65V Electrolytic Capacitor
      • L1 .................. Inductor 5uH *Ver Texto

    • Others
      • P1, P2 ............ Screw Terminal Type 5mm 2-Pin Connector
      • P3 .................. Screw Terminal Type 5mm 3-Pin Connector
      • J1 ....................Set of male connectors 2-Pin (Optional)
      • Other .............. PCB, Wires, Speaker, Heat Sink, etc.

    Power Supply

    Power is supplied through a 24 VAC transformer with center tape, i.e. [+VAC | GND | -VAC], after rectification the source will supply 35 VDC

    It is a standard power supply voltage for this amplifier to work with little heating and little distortion, as it works with a minimum of 18V and a maximum of 84V

    The current to power this amplifier is of at least 2A, and if it is going to using in stereo mode, two of these same ones, this current has to be doubled to 4 Amperes

    In Figure 3 below, we have a suggestion for a power supply that we use in our projects. In this article, besides having the schematic diagram with the Printed Circuit Board, you will understand how to easily calculate your own Power Supply, with the desired voltage.

    You can in the link below:

    Fig. 3 - Symmetrical Power Supply for Power Amplifiers

    Printed Circuit Board

    In Figure 3, we provide the PCB - Printed Circuit Board, in GERBER, PDF and PNG files. These files are available for free download, on the MEGA server, in a direct link, without any bypass. 

    All to make it easier for you to do a more optimized assembly, either at home, or with a company that prints the board. You can download the files in the Download option below.

    Fig. 4 - PCB - High Performance 56W Audio Power Amplifier using LM3876 IC

    Files to download, Direct Link:

    Click on the link beside: GERBER, PDF and PNG files

    If you have any questions, suggestions or corrections, please leave them in the comments and we will answer them soon.

    Subscribe to our blog!!! Click Here - elcircuits.com!!!

    My Best Regards!!!


    Monday, January 24, 2022

    14.4V, 70W High Efficiency Power Amplifier using TDA1562Q IC + PCB

    Fig. 1 - 14.4V, 70W High Efficiency Power Amplifier using TDA1562Q IC + PCB

    The original project: Click Here!

    This is a high efficiency and high power amplifier, powered by a simple 14.4V power supply, can provide a power of 70W in , using the TDA1562Q Integrated Circuit.

    The TDA1562Q IC is a monolithic Class H power amplifier in Bridge-Tied Load (BTL) mode in a 17-lead DIL-folded-SIL plastic package.

    The device can be used for general-purpose audio systems, however, given its low operating voltage, between 8V and 18V.

    We can use it in: Car Sound, Subwoofer Boxes, as well as applications powered by a DC power supply connected to the mains, such as: speaker system, guitar amplifier, TV Sound, or in portable audio like Boombox, Etc.

    Features

    • Very high output power, operating from a single low supply voltage
    • Low power dissipation, when used for music signals
    • Switches to low output power at too high case temperatures
    • Few external components
    • Fixed gain
    • Differential inputs with high common mode rejection
    • Mode select pin (on, mute and standby)
    • Status I/O pin (class-H, class-B and fast mute)
    • All switching levels with hysteresis
    • Diagnostic pin with information about:–  Dynamic Distortion Detector (DDD)–  Any short-circuit at outputs–  Open load detector–  Temperature protection.
    • No switch-on or switch-off plops

    The Schematic

    In Figure 2 below we have the schematic diagram of the High Efficiency Power Amplifier circuit and we can follow and analyze all the simplicity of the circuit, and as we can see, it is a circuit of easy assembly, and with few external components.

    Fig. 2 - Schematic 14.4V, 70W High Efficiency Power Amplifier using TDA1562Q IC

    Power Supply

    This amplifier is powered by a simple positive and negative voltage type power supply, and has a supply voltage range that varies with a minimum voltage of 8V and a maximum voltage of 18V, the typical unstressed working voltage of the Integrated Circuit is 14.4V

    The power supply should have a current of at least 5 Amperes, to be used in mono mode, if mounting in the stereo, "two channel" version, the current should be doubled, and should also be provided with good filtering to avoid ripples in the system, which can cause noise in the amplifier.

    The impedance of this amplifier to reach its full power is , however we can set it to , however we will not get the maximum power of the amplifier.

    Component List

    • Semiconductors
      • CI1 ............ TDA1562Q Integrated Circuit 
      • LD1 ........... LED Light Emitting Diode

    • Resistors
      • R1 .............. 1MΩ resistor (brown, black, green, gold)
      • R2 .............. 10KΩ resistor (brown, black, orange, gold) 
      • R3 .............. 5.6KΩ resistor (green, blue, orange, gold)  

    • Capacitors
      • C1, C2 ....... 470nF Ceramic / Polyester Capacitor
      • C3 .............. 10uF / 63v Electrolytic Capacitor
      • C4, C5 ....... 4700uF / 25V Electrolytic Capacitor
      • C6 .............. 100nF Ceramic / Polyester Capacitor
      • C7 .............. 2.200uF / 25V Electrolytic Capacitor

    • Others
      • P1, P2, P3 ... Screw Terminal Type 5mm 2-Pin Connector
      • Others ......... Heat sink for IC, wires, connectors, PCB, tin etc.

    Printed Circuit Board

    In Figure 3, we provide the PCB - Printed Circuit Board, in GERBER, PDF and PNG files. These files are available for free download, on the MEGA server, in a direct link, without any bypass. 

    All to make it easier for you to do a more optimized assembly, either at home, or with a company that prints the board. You can download the files in the Download option below.

    Fig. 3 -  PCB 14.4V, 70W High Efficiency Power Amplifier using TDA1562Q IC


    Files to Download, Direct Link:

    Click on the link beside: GERBER, PDF and PNG files

    If you have any questions, suggestions or corrections, please leave them in the comments and we will answer them soon.

    Subscribe to our blog!!! Click Here - elcircuits.com!!!

    My Best Regards!!!


    Friday, January 21, 2022

    170W AB Class Bridge Mode Amplifier using TDA7294 IC + PCB

    Fig. 1 - 170W AB Class Bridge Mode Amplifier using TDA7294 IC + PCB

    Para Versão em Português, Clique Aqui!

    This is a Class AB Audio Power Amplifier, it uses two TDA7294 Integrated Circuits, in Bridge Mode to drive one or more power speakers.

    The circuit provides a total output power of 170W, and this with good sound quality, powered from a symmetrical power supply.

    The Amplifier responds very well to all audible frequency ranges, and has a minimalist, compact design, which makes this amplifier a good choice for an unprecedented range of application. 

    IC Description

    The TDA7294 is  a monolithic integrated circuit in Multiwatt15  package, intended  for  use  as  audio class   AB   amplifier   in   Hi-Fi   field   applications (Home Stereo, self powered loudspeakers, guitar amplifier, Top-class TV). 

    Thanks to the wide voltage range and to the high out current capability it is able to supply the highest power into both 4Ω and 8Ω loads even in  presence of  poor supply regulation, with high Supply Voltage Rejection.

    The  built  in  muting  function  with  turn  on  delay simplifies the remote operation avoiding switching on-off noises.

    You might also be interested in:

    The main Advantages offered by Bridge solution

    • High power performance with voltage level limiting supply.
    • Considerably high output power, even at high load values (i.e. 16 Ohm).
    • For a Speaker with 8Ω, Vs = ± 25V, the maximum output power obtained is 150 W, while with a Speaker with 16Ω, Vs = ± 35V, the maximum power is 170 W.

    Features

    • Operating Voltage Range (± 10V to ±40V)
    • DMOS Output Stage
    • High Output Power (Up to 100W musical)
    • Muting / Stand-By Functions
    • No Switch On/Off Noise
    • No Boucherot Cells
    • Very Low Distortion
    • Very Low noise 
    • Short-circuit protection
    • Thermal shutdown

    Bridge Application

    Our amplifier is configured in Bridge mode, where two TDA7294s ICs are used. With this type of configuration we get a pretty significant 170W of power, however there are two different configurations: 

    For 8Ω Speaker - Vs = ± 25V, the maximum output power is 150 W.
    For 16Ω Speaker - Vs = ± 35V, the maximum power is 170 W.

    We know that the TDA7294, supports or speakers in mono version, however, for this application in Bridged configuration, the speaker impedance shouldn't be less than for reasons of dissipation and current carrying capacity of the Integrated Circuits.

    The Schematic Circuit

    In Figure 2 below we have the arrangement of the components of the amplifier circuit with the two TDA7294 ICs, and as we can see, the difficulty is not extreme.

    Since there are few external components, making the amplifier circuit very simple to assemble, and a technician or hobbyist with average experience can assemble it without much difficulty. 

    It is important to remember to be careful when assembling the circuit, not to invert any component such as capacitor diodes, or even when connecting the symmetrical voltage of the power supply.

    Not to invert the voltage poles, because the integrated circuit or other components can be damaged.

    Fig. 2 - Schematic 170W Amplifier Circuit in Bridge with Integrated Circuit TDA7294

    Components List

    • Semiconductors
      • U1, U2 ........................ TDA7294 Integrated Circuit 
      • D1 ............................... 1N4148 Silicon Diode

    • Resistors
      • R1, R5, R6, R8, R10 ... 22K Resistor (red, red, orange, gold)
      • R2 ................................ 20K resistor (red, black, orange, gold)
      • R3 ................................ 10K resistor (brown, black, orange, gold)
      • R4 ................................ 30K resistor (orange, black, orange, gold)
      • R7, R9 ......................... 680Ω resistor (blue, gray, black, gold)

    • Capacitors
      • C1, C4 ......................... 1μF Ceramic/Polyester Capacitor
      • C2, C3, C5, C6 ............ 22μF Electrolytic Capacitor

    • Others
      • P1, P2 ......................... Screw Terminal Type 5mm 2-Pin Connector
      • P3 ................................ Screw Terminal Type 5mm 3-Pin Connector
      • J1 .................................Set of male connectors 3-Pin (Optional)
      • Other ........................... PCB, Wires, Speaker, etc.

    Power Supply

    The power supply will depend on which output power you will choose, which will also depend on how many Ohms your speaker will have. We have two versions:

    Version 1 - 150W output.

    • Speaker must be 8Ω and the maximum voltage is for ±25V

    Version 2 - 170W output.

    • Speaker must be 16Ω and the maximum voltage is ±35V.

    Remember that for both versions a Symmetrical power supply is used, i.e. [ +VCC | GND | -VCC ]. With a current of at least 6 Amperes.

    Printed Circuit Board

    In Figure 3, we provide the PCB - Printed Circuit Board, in GERBER, PDF and PNG files. These files are available for free download, on the MEGA server, in a direct link, without any bypass. 

    All to make it easier for you to do a more optimized assembly, either at home, or with a company that prints the board. You can download the files in the Download option below.

    Fig. - PCB 170W AB Class Bridge Mode Amplifier using TDA7294 IC

    Files to download, Direct Link:

    Click on the link beside: GERBER, PDF and PNG files

    If you have any questions, suggestions or corrections, please leave them in the comments and we will answer them soon.

    Subscribe to our blog!!! Click Here - elcircuits.com!!!

    My Best Regards!!!

    Tuesday, January 11, 2022

    HI-FI 120W RMS Amplifier Circuit using LM4780 IC + PCB

    Fig. 1 - HI-FI 120W RMS Amplifier Circuit using LM4780 IC

    This is a HI-FI Audio Amplifier circuit with high quality with a large frequency response, using the Integrated Circuit LM4780 which is a stereo audio amplifier. 

    Capable of providing normally 60W per channel of average power of continuous output on an load with less than 0.5% THD + N from 20Hz to 20kHz.

    LM4780 General Description

    The LM4780 is fully protected utilizing National’s Self Peak Instantaneous TemperatureKe) (SPiKeTM) protection circuitry. 

    SPiKe provides a dynamically optimized Safe Operating Area (SOA). SPiKe protection completely safeguards the LM4780’s outputs against over-voltage, under-voltage, overloads, shorts to the supplies or GND, thermal runaway and instantaneous temperature peaks. 

    The advanced protection features of the LM4780 places it in a class above discrete and hybrid amplifiers.

    Each amplifier of the LM4780 has an independent smooth transition fade-in/out mute. The LM4780 can easily be configured for bridge or parallel operation for 120W mono solutions.

    Key Specifications

    • Output Power/Channel with 0.5% THD+N, 1kHz into 8Ω 60W (typ)
    • THD+N at 2 x 30W into 8Ω (20Hz - 20kHz) 0.03% (typ)
    • THD+N at 2 x 30W into 6Ω (20Hz - 20kHz) 0.05% (typ)
    • THD+N at 2 x 30W into 4Ω (20Hz - 20kHz) 0.07% (typ)
    • Mute Attenuation 110dB (typ)
    • PSRR 85dB (min)
    • Slew Rate 19V/µs (typ

    The Circuit

    In Figure 2 below, we have the arrangement of the amplifier circuit components with the LM4780 IC, and as we can see, there are few external components. 

    It is making the amplifier circuit very simple to assemble, one must be careful when assembling the circuit, so as not to invert any component, as it may suffer circuit burnout.

    Fig. 2 - Schematic diagram of Hi-Fi Amplifier 120W RMS with IC LM4780

    Features

    • SPiKe protection
    • Few external components
    • Silent fade-in / mute out mode
    • Wide range of supply voltage: 20V - 84V
    • Signal-to-noise ratio ≥ 97dB (ref. for PO = 1W)

    Power Supply

    The power supply is a +-35V symmetric power supply. If you want to use it in stereo mode with two channels, it will be necessary to use twice the current to support the power of 240W, 120W per channel.

    The power supply must have a good filter to avoid roaring, interference, and oscillations in the amplifier output.

    The consumption current for a channel "One integrated circuit", must be 4 amps, if using two circuits, in stereo mode, the current must be doubled, in this case 8 amps.

    The LM4780 must be equipped with a heatsink, if you use the IC without the heatsink, it will burn out.

    It is recommended to tinker the voltage and output tracks, since the IC has a tight pinout, making it impossible to widen the tracks on the PCB.

    Component List

    • Semiconductors
      • U1 ........................ Integrated Circuit LM4780

    • Capacitors
      • C1 ........................ 1uF Polyester / Ceramic Capacitor
      • C2 ........................ 4.7uF - 50V Electrolytic Capacitor
      • C3, C5, C8, C9 ... 0.1uF Polyester / Ceramic Capacitor
      • C4 ........................ 4.7uF Polyester / Ceramic Capacitor
      • C6, C7 ................. 47uF - 50V Electrolytic Capacitor

    • Resistors:   
      • R1, R6, R7 .......... 47k ohm resistor - (yellow, violet, orang, gold)
      • R2 ....................... 10k ohm resistor - (brown, black, orange, gold)
      • R3, R5 ................ 4.7k ohm resistor - (yellow, violet, red, gold)
      • R4 ....................... 3.3k ohm resistor - (orange, orange, red, gold)
      • R8, R9 ................ 2.7 ohm resistor - (red, violet, red, gold)

    • Others
      • SW1 ................... Switch on/off - to mute "optional"
      • P1, P2 ................. Screw Terminal Type 5mm 2-Pin Connector
      • P3 ....................... Screw Terminal Type 5mm 3-Pin Connector
      • PCB, Wires, Solders, Speaker and Etc.

    In Figure 4, we provide the PCB - Printed Circuit Board, in GERBER, PDF and PNG files. These files are available for free download, on the MEGA server, in a direct link, without any bypass. 

    All to make it easier for you to do a more optimized assembly, either at home, or with a company that prints the board. You can download the files in the Download option below.

    Fig. 3 - PCB HI-FI 120W RMS Amplifier Circuit using LM4780 IC

    Files to Download, Direct Link:

    Click on the link beside: GERBER, PDF and PNG files

    If you have any questions, suggestions or corrections, please leave them in the comments and we will answer them soon.

    Subscribe to our blog!!! Click Here - elcircuits.com!!!

    My Best Regards!!!