4 x 50W High Power Amplifier, 14.4V - IC TDA7563A + PCB

PCB 4 x 50W High Power Amplifier, 14.4V - IC TDA7563A

🌐 You can read this article in: Portuguese | Español

Hello, electronics enthusiasts!

This is a 200W High Power Amplifier Circuit, and its great trump card is that it works with a simple power source and still at 14.4V, which means we can plug in a 12V car battery, or motorbike battery, or UPS battery, etc.

Also, the circuit is very easy to build as it requires very few external components.

The TDA7563A is a quad-bridge type amplifier of BCD technology in Flexiwatt27 and Power SO36 packages designed specifically for car radio applications.

Thanks to the DMOS output stage, the TDA7563A has very low distortion, which allows for clear and powerful sound. 

Features include its superior efficiency performance resulting from the unique internal system structure, making it the device best suited to simplify thermal management in high power packages.

This device is equipped with a complete diagnostic matrix that communicates the status of each speaker via the I2C bus.

💡 Features

• Multiple Power BCD Technology
• MOSFET output power stage
• DMOS power output
• New high efficiency technology (SB class)
• High output power capacity 4x28W / 4Ω @ 14.4V, 1kHz, 10% THD, maximum power 4x50W
• Maximum output power 4x72W / 2Ω
• Complete conduction of I2C bus:
• Standby
• Front/rear independent, smoothed play/mute
• Selectable 26dB / 12dB gain (for low noise line output function)
• Enable / disable high efficiency
• I2C bus digital diagnostics (including DC AC load detection)
• Total failure protection
• DC offset detection
• Four independent short circuit protection
• Cutting Detector Pin with Selectable Threshold (2% / 10%)
• Standby/mute pin
• Linear thermal shutdown with multiple thermal warnings
• ESD protection

🔌 Amplifier Circuit Diagram

In Figure 2 below, you can see the schematic of the High Efficiency Power Amplifier. We can understand and analyze the simplicity of the circuit and see that it is an easy to assemble circuit with few external components.

Fig 2 - Schematic Diagram 4 x 50W High Power Amplifier, 14.4V - IC TDA7563A

You might also be interested in:

• 170W AB Class Bridge Mode Amplifier using TDA7294 IC + PCB
• High Fidelity 14W - 12V Power Amplifier using TDA2030 IC + PCB
• 24W Stereo Hi-Fi Audio Amplifier using TDA2616 + PCB
• 4 x 50W High Power Amplifier, 14.4V - IC TDA7563A + PCB
• HI-FI 120W RMS Amplifier Circuit using LM4780 IC + PCB
• 180W RMS 4-Channel Amplifier with TDA7386 + PCB
• 320W Power Audio Amplifier, Powered with 14.4V - 2Ω with IC TDA7560 + PCB
• 100W RMS Audio Amplifier IC TDA7294 + PCB
• 200W RMS Stereo Power Amplifier with IC STK4231II + PCB

⚡ Power Supply

This amplifier is powered by a single positive and negative voltage power supply and has a supply voltage range that varies with a minimum voltage of 8V and a maximum voltage of 18V. 

The typical working voltage with no load on the integrated circuit is 14.4V.

The power supply must have a current of at least 5 amps to be used in mono mode, when mounted in stereo version, "two channels", the current must be doubled, and it must also be provided with a good filtering to avoid a ripples system that can cause noise in the amplifier.

The working impedance value of this amplifier to reach its total power is 4 ohms, but we can also set it to 8 ohms, but then we will not get the maximum power from the amplifier.

🧾 Bill of Materials

• CI1 ......................... Integrated Circuit TDA7563A
• C1, C2, C3, C4 ...... 220nF Ceramic / Polyester Capacitors
• C5 ........................... Capacitors 1uF / 63v
• C6 ........................... Electrolytic Capacitor 10uF / 63v
• R1 ........................... 47K Ohm resistors
• R2 ........................... 8K2 ohm resistor
• R3 ........................... Resistor 4K7 ohms
• P1 to P9 .................. KF301 solderable 2-Pin Bolt-On Connector (Optional)
• J1............................. 3 Ways 1x3 Weldable Male Pin Bar
• Others ..................... Heatsink for IC, wires, connectors, PCI, tin etc.

🖨️ Printed Circuit Board (PCB) - Download

We are making the PCI available in GERBER, PDF and JPEG files, for those who want to create a more optimized assembly, either at home, or if you prefer, at a company that prints the board.

📥 Files to Download, Direct Link:

Click on the link beside: Layout PCB, PDF, GERBER, JPG

👋 I hope you enjoyed it!!!

If you have any questions, suggestions or corrections, please leave them in the comments and we will answer them soon.

🙏 Subscribe to our blog!!! Click here - elcircuits.com!!!

My Best Regards!!!